Eden HA2000 Spezifikationen PDF herunterladen (Seite 17)

PROBLEM? 17

Do not HESITATE to call us via our assistance hotline (at the end of the notice). Our technicians will have the pleasure to

help you make a perfect installation.

If the Control Panel doesn’t receive the

Supervisory signals transmitted from a certain

PIR, an “Out-Of-Order” fault message will be

generated.

z Sleep Timer

The PIR has a “sleep time” of approximately 1

minute to conserve power. After transmitting a

detected movement, the PIR will not retransmit

for 1 minute; any further movement detected

during this sleep period will extend the sleep

time by another minute. In this way continuous

movement in front of a PIR will not unduly

exhaust the battery.

z Test mode

The PIR can be put into Test mode by pressing

the Test Button aka LED on the front cover. In

Test mode, it will disable the sleep timer and will

enable the LED indicator to flash every time a

movement is detected. Each time press the Test

Button, the PIR will transmit a test signal to the

Control Panel for radio range test and enter the

test mode for 3 mins. It will exit Test Mode

automatically after 3 mins and returns to normal

mode.

z LED Indicator

In Normal operation mode, the LED Indicator

will not light except in the following situations:

z When the PIR is in low battery condition,

every time it transmits a detected

movement, the LED will light up for about

2 seconds.

z When the cover is opened and the tamper

switch is violated, the LED will light up for

2 sec. to indicate it is transmitting the

“Tamper” signal.

z When the Tamper condition persists, every

time it transmits a detected movement, the

LED will light up.

However, if the PIR is in Test mode, the LED

will light up every time a movement is detected.

z Battery

z The PIR uses one 3.6 V Lithium battery as

its power source. The PIR will have a

typical battery life of 5 years at an average

of 20 activations a day.

z Low battery detection operates at a

threshold of 3.2V+/-2.4% where the PIR has

enough reserve energy to typically operate

for 1 month before complete exhaustion. A

low battery signal will be sent to the Control

Panel along with regular signal

transmissions for the Control Panel to

display the status accordingly.

z For each installation, the battery is installed

in by the factory before shipment with an

Insulator inserted.

z Getting Started

z Pull out the battery Insulator steadily.

z The LED indicator steadily flashes for 30

seconds. (The PIR is warming up). During

the warming period, the PIR will not be

activated. It is recommended that you stay

away from the detection area during this

time. After the warming period is over, the

light will turn off and the PIR will be ready

for operation.

z The Control Panel is already into “Device

+/-“ menu and then select “Add Device”

menu.

z Press the test buttons on the front cover.

Step B5. After the detected PIR Detector is

confirmed, you are requested to choose

between “Burglar”, “Home Omit”,

“Entry”, “Home Delay” device mode.

B u r g l a r

Home O m i t

Ent r y

Home D e l ay



For detailed functional descriptions of

PIR Detector in these 4 different device

modes, please refer to the Note section

following Step A5 for adding Door

Contact.

) “B” for Burglar PIR Detector

) “O” for Home Omit PIR Detector

) “E” for Entry PIR Detector

) “D” for Home Delay PIR Detector

StepB6. Make a selection and press “OK”. The

screen will then prompt you to select the

Instant attribute if the selected device

mode supports the option.

I n s t a n t O f f

I n s t a n t O n



For detailed functional descriptions of

PIR Detector with or without the Instant

attribute, please refer to the Note section

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 40 41

Kommentare zu diesen Handbüchern

Keine Kommentare

Eden HA2000 Spezifikationen Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Eden HA2000