Eden HA2000 Spezifikationen PDF herunterladen (Seite 9)

PROBLEM? 9

Do not HESITATE to call us via our assistance hotline (at the end of the notice). Our technicians will have the pleasure to

help you make a perfect installation.

2. Master PIN code

z Master PIN code is used for accessing the

programming mode and it is set to “0000” as

factory default. Before you set your own Master

PIN code, “0000” has to be keyed in every time it

is required.

z To set your Master PIN code

Step 1. Use the arrow keys to select “Master PIN

code” and press “OK”

E n t e r N e w C o d e

. . . .

Step 2. You can key in your preferred 4-digit

number and then press “OK”

R e p e a t N e w C o d e

. . . .

Step 3. You are prompted to re-enter the same

code again and press “OK”

If the code is correct, the screen returns

to “General Setting” menu, setting the

Master PIN code is completed.



) If the code is not correct, a “Code is not

correct” prompt message will be

displayed 2 sec., and you are requested

to repeat Step 3 to enter again.

) It is recommended to set “Master PIN

code” different from the rest user codes,

where one responsible person has

programming access only, however, it

can be the same as one of the user code

for easier use.

N

>



When entering the following individual setting

screens, the value displayed on the screen or the

option that the cursor underlined is the current

setting of each item.

If it is not necessary to change the current setting,

just press “

“ to escape.

3. Entry Time

This is for you to select the Entry Delay time.

Options available are 0 sec., 10 sec., 20 sec., up

to 70 sec. in 10-sec increments.

E n t r y T i m e

1 0 s e c .

z Use “S”,“T” keys to switch between

options.

z Press “OK” to confirm.

z 10 sec. is set as factory default.



) Entry Delay time applies only to the zone

that a Door Contact or PIR Detector is

installed and is set to “Entry”.

4. Exit Time

This is for you to select the Exit Delay time.

Options available are 0 sec., 10 sec., 20 sec. up

to 70 sec. in 10-sec increments.

E x i t T i m e

1 0 s e c .

z Use “S”,“T” keys to switch between

options.

z Press “OK” to confirm.

z 10 sec. is set as factory default.

5. Alarm Length

This is for you to select the period of time that the

built-in siren will sound when an alarm is

activated. You can choose from 1 min. to 10 min.

in 1-min increments.

A l a r m L e n g t h

0 3 m i n .

z Use “S”,“T” keys to switch between

options.

z Press “OK” to confirm.

z 3 minutes is set as factory default.

6. C.U. Siren

This is for you to decide whether the built-in siren

will sound or not when an alarm is activated.

C . U . S i r e n O n

C . U . S i r e n O f f

z Press “S”,” T” keys to select the option.

z Press “OK” to confirm.

z “C.U. Siren On” is set as factory default.

7. C.U. Tamper

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 40 41

Kommentare zu diesen Handbüchern

Keine Kommentare

Eden HA2000 Spezifikationen Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Eden HA2000